Tel : +86-18059296519
Whatsapp : +8618059296519
Email : [email protected]
Pipe Elbows are installed between two lengths of pipe or tubing to allow a change of direction, usually at a 90°or 45°angle.
Size :
Seamless Type: 1/2" -20”(DN15-DN500) Welded Type：1/2--48”(DN15-DN1200)Standard :
GB/T12459, GB/T13401, SH3408, SH3409; ASME/ANSIB16.9, B16.28, ASTMA403, MSS SP-43; DIN2605, DIN2609, DIN2615, DIN2616; JIS B2311, JIS B2312, JIS B2313Material :
TP304; TP304H; TP304L; TP316; TP316L; TP321; TP321H; TP317L; TP310S; TP347HProcess :
Cold&Mandrel FormingSchedules :
Sch5s-Sch80s; Sch10-Sch160; XS-XXSStainless Steel Elbow In Pipe-EC2
Steel pipe elbow (sometimes also refereed as bends) is a key part in a pressure piping system used to change the fluid flow direction. It is used to connect two pipes with same or different nominal diameters, and to make the pipe and thus the fluid direction turn to a certain direction of 45 degree or 90 degree.
Classification of Steel Pipe Elbows
Steel pipe elbows can be classified through following various parameters:
According to fluid flow direction of the pipes, elbows can be divided into different degrees, such as 45 degree, 90 degree, 180 degree, which are most common elbows. Also there are 60 degree and 120 degree elbows for some special pipelines. This degree is just an representation of the angle by which the fluid flow is going to change after flowing through the said elbow.
|
Standard： |
ASTM EN DIN GB ISO JIS |
|
Certification： |
SGS，ISO，ROHS |
|
Size： |
1/2"-20" seamless, 1/2--48” welded |
|
Wall thickness： |
SCH5S, SCH10S, SCH10, SCH40S, STD, XS, SCH80S, XXS, SCH20, SCH30, SCH40, SCH60, SCH80, SCH160, XXS and etc. |
|
Radius： |
LR/long radius/R=1.5D,SR/Shrot radius/R=1D, various radius: 3D,4D,5D,6D,7D,10D,20D etc. |
|
End： |
Bevel end/BE/buttweld |
|
Camber： |
30º 40º 60º 90º 180º,etc |
|
Polish： |
mirror polish,dull/matte polish,sub-light,240 girt,400 grit |
|
Surface： |
Pickled,sand blasting, rolling blast,brighten,matt polished,mirror polished,vanished,shinning |
|
Process Method： |
Forged / Casting |
|
Price terms： |
FOB,CFR,CIF,EXW all acceptable |
|
Grade： |
201，304,304L，309，309S，310S，316,316L，316Ti，317L，321,347H，409,409L，410，410S，420（420J1，420J2），430，436，439，441，444，446 ，2205，2207，etc |
|
1.4301, 1.4307, 1.4541, 1.4401, 1.4404 ,1.4571, 1.4438, 1.4539, 1.4547, 1.4529, 1.4562, 1.4410, 1.4878, 1.4845, 1.4828, 1.4876,2.4858, 2.4819，etc |
Pipe Elbows are installed between two lengths of pipe or tubing to allow a change of direction, usually at a 90°or 45°angle.
Pipe Elbows are installed between two lengths of pipe or tubing to allow a change of direction, usually at a 90°or 45°angle.
Pipe Elbows are installed between two lengths of pipe or tubing to allow a change of direction, usually at a 90°or 45°angle.
Pipe Elbows are installed between two lengths of pipe or tubing to allow a change of direction, usually at a 90°or 45°angle.
Pipe Elbows are installed between two lengths of pipe or tubing to allow a change of direction, usually at a 90°or 45°angle.
No.1633, Binhai Road, Wenzhou Economic Development Zone, Wenzhou, China
IPv6 network supported
